Multitech MultiVOIP 800 MVP800 User's Guide download pdf (Page 20)

MultiVOIP 400/800 User Guide

Cabling Procedure

Cabling involves connecting the master MultiVOIP to your LAN and telephone equipment.

1. If you are connecting any Voice/Fax Channel to an E&M trunk other than type 2, perform the

E&M Jumper Block Positioning procedure before connecting power to the unit.

2. Connect one end of the power supply to a live AC outlet and connect the other end to the

MultiVOIP as shown in Figure 2-2. The power connector is a 7-pin circular DIN connector.

E&M FXO FXS E&M FXO FXS E&M FXO FXS

VOICE/

FAX

CHANNEL

VOICE/

FAX

CHANNEL

VOICE/

FAX

CHANNEL

VOICE/

FAX

CHANNEL

VOICE/

FAX

CHANNEL

VOICE/

FAX

CHANNEL

VOICE/

FAX

CHANNEL

VOICE/

FAX

CHANNEL

CHANNEL 10

CHANNEL 9

CHANNEL 8

CHANNEL 7

CHANNEL 6

CHANNEL 5

CHANNEL 4

CHANNEL 3

CHANNEL 2 (RS232/V.35)

CHANNEL 1 (RS232/V.35)

10BASET

ETHERNET

COMMAND PORT

EXT. COMPOSITE LINK (RS232/V.35)

POWER

GND

T1 DSU

MONITOR

XMT RCV

INTERNAL

COMPOSITE

LINK

E&M FXO FXS

Ethernet Connection

Command Port Connection

Power Connection

FXS

FXO

E&M

FXSE&M

FXO

PSTN

Voice/Fax Channel 1 - 8

Connections

Figure 2-2. Cable Connections

3. Connect the MultiVOIP to a PC by using a DB-25 (male) to DB-9 (female) cable. Plug the DB-25

end of the cable into the Command port of the MultiVOIP and the other end into the PC serial

port. See Figure 2-2.

4. Connect a network cable to the ETHERNET 10BASET connector on the back of the MultiVOIP.

Connect the other end of the cable to your network.

5. If you are connecting a station device (e.g., analog telephone, fax machine, or Key Telephone

System (KTS) to your MultiVOIP, connect one end of an RJ11 phone cord to the Voice/Fax

Channel 1 FXS connector on the back of the MultiVOIP and the other end to the station device.

If you are connecting the station side of a telephone switch (PBX) to your MultiVOIP, connect one

end of an RJ11 phone cord to the Voice/Fax Channel 1 FXO connector on the back of the

MultiVOIP and the other end to the phone jack.

If you are connecting an E&M trunk from a telephone switch to your MultiVOIP, connect one end

of an RJ45 phone cord to the Voice/Fax Channel 1 E&M connector on the back of the MultiVOIP

and the other end to the trunk. Refer to Appendix B for E&M cabling pinout.

If you are connecting to an E&M trunk, you need ensure that the E&M trunk jumper is in the

correct position for the E&M type trunk. The default E&M jumper position is E&M type 2. To

change the E&M jumper position, perform the E&M jumper block positioning procedure.

6. Repeat the above step to connect the remaining telephone equipment to each Voice/Fax

Channel on your MultiVOIP.

7. Turn on power to the MultiVOIP by placing the ON/OFF switch on the back panel to the ON

position. Wait for the BTG LED on the MultiVOIP to go OFF before proceeding. This may take a

couple of minutes to go OFF.

Proceed to the next section to load the MultiVOIP software.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 110 111

Comments to this Manuals

No comments

Multitech MultiVOIP 800 MVP800 User's Guide Page 20

Comments to this Manuals

Related products and manuals for Networking Multitech MultiVOIP 800 MVP800