Multitech MULTIVOIP MVP-810ST User's Guide download pdf (Page 42)

Connectivity Test MultiVOIP FX Quick Start Guide

8. Read console messages recorded on HyperTerminal.

Console Messages from Originating VOIP. The voip unit that originates the call will send back messages

like that shown below.

[00026975] CAS[0] : RX : ABCD = 1, 1, 1, 1,Pstn State[1] TimeStamp : 26975

[00027190] CAS[0] : TX : ABCD = 1, 1, 1, 1

[00027190] PSTN: cas seizure detected on 0

[00027440] CAS[0] : TX : ABCD = 0, 0, 0, 0

[00033290] PSTN:call detected on 0 num=17637175662*

[00033290] SIP[0]:destAddr = TA:200.2.10.5:1720,NAME:Mounds

View,TEL:17637175662,17637175662

[00033290] SIP[0]:srcAddr = NAME:New York,TA:200.2.9.20

[00033440] SIP [0]:cmCallStateProceeding

[00033500] SIP[0]: Remote Information (Q931): MultiVOIP - T1

[00033565] CAS[0] : TX : ABCD = 1, 1, 1, 1

[00033675] SIP [0]: MasterSlaveStatus=Slave

[00033675] SIP[0]:FastStart Setup Not Used

[00033690] CAS[0] : TX : ABCD = 1, 1, 1, 1

[00033755] SIP[0]: Coder used 'g7231'

[00033810] PSTN:pstn call connected on 0

Console Messages from Terminating VOIP. The voip unit connected to the phone where the call is

answered will send back messages like that shown below.

[00170860] SIP[0]: New incoming call

[00170860] PSTNIF : Placing call on channel 0 Outbound digit 7175662

[00170885] CAS[0] : TX : ABCD = 1, 1, 1, 1

[00171095] SIP [0]: MasterSlaveStatus=Master

[00171105] CAS[0] : RX : ABCD = 1, 1, 1, 1,Pstn State[7] TimeStamp : 171105

[00171105] SIP[0]: Coder used 'g7231'

[00171110] SIP[0]:FastStart Setup Not Used

[00171110] SIP[0]: Already opened the outgoing logical channel

[00171110] SIP[0]: Coder used 'g7231'

[00171315] CAS[0] : RX : ABCD = 0, 0, 0, 0,Pstn State[9] TimeStamp : 171315

[00172275] PSTN: dialing digit ended on 0

[00172285] PSTN: pstn proceeding indication on 0

[00172995] CAS[0] : RX : ABCD = 1, 1, 1, 1,Pstn State[12] TimeStamp : 172995

[00173660] CAS[0] : TX : ABCD = 1, 1, 1, 1

[00173760] PSTN:pstn call connected on 0

9. When you see the following message, end-to-end voip connectivity has been achieved.

“

PSTN: pstn call connected on X”

where x is the number of the voip channel carrying the call

10. If the HyperTerminal messages do not confirm connectivity, go to the Troubleshooting procedure

below.

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 192 193

Comments to this Manuals

No comments

Multitech MULTIVOIP MVP-810ST User's Guide Page 42

Comments to this Manuals

Related products and manuals for Networking Multitech MULTIVOIP MVP-810ST