Multitech MultiModem Cell MTCBA-C1 User's Guide Page 67
- Page / 135
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 13 – OMA / DM Control Commands
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide (PN S000478C) 67
Wavecom Device Services Wavecom +WDSW
Description: This Wavecom proprietary command allows carrier- or customer-specific configuration of Device
Services.
Syntax: Command Syntax: AT+WDSW=<Operation>,<Action>
Command Possible Responses
AT+WDSW=? ERROR
AT+WDSW=12,0
Note: Clear auto-registration complete
OK
AT+WDSW=12,1
Note: Mark auto-registration complete
OK
AT+WDSW?
Note: Display auto-registration state
+WDSW: 12,1
Note: Auto-registration is complete
AT+WDSW?
Note: Display auto-registration state
+WDSW: 12,0
Note: Auto-registration is incomplete.
Values: <Operation>
12 Auto-registration. This operation allows auto-registration status to be set or
cleared. The Service Provisioning Code must be entered using the +WSPC
command prior to attempting to set or clear auto-registration.
<Action>
0 Clear auto-registration. Auto-registration will be attempted after the next power
cycle.
1 Mark auto-registration complete. No further auto-registration attempts will be
made.
Parameter Storage: Parameters are stored in flash without using the AT&W command. AT&F has no
effect on these parameters.
Note: The auto-registration operation is available for only for modem configured for the Sprint network.
Wavecom Device Services Indications +WDSI
Description: This Wavecom proprietary command allows a user to select which Device Services events are
reported. Device Services events are reported through the +WDSI unsolicited response.
Syntax: Command Syntax: AT+WDSI=<Level>
Command Possible Responses
AT+WDSI? +WDSI: <Level>
OK
AT+WDSI=? +WDSI: (0-8388607)
OK
AT+WDSI=8388607
Note: Enable all Device Services event notifications
OK
AT+WDSI
Note: Enable all Device Services event notifications
(default)
OK
+WDSI: <Event>[,<Data>]
Note: Unsolicited response
OK
Values: <Level> Indications level, bit field (default value = 0)
bit set to 0: indication deactivated
bit set to 1: indication activated
0 No indication
1 (bit 0) Reserved
2 (bit 1) Reserved
4 (bit 2) Activate the authentication indications (<Event> = 4 & 5)
8 (bit 3) Activate the session start indication (<Event> = 6, 7 & 8)
16 (bit 4) Activate the package download indications (<Event> = 9, 10 & 11)
32 (bit 5) Reserved
64 (bit 6) Activate the update indications (<Event> = 14, 15 & 16)
- CDMA-C1 AT Commands 1
- Contents 3
- Chapter 1 – Introduction 7
- Chapter 2 – AT Commands 8
- Overview 8
- Command Types 9
- Command Format and Syntax 9
- Input Command Syntax 10
- Other Syntax 10
- Output Response Syntax 10
- Parameter Defaults 10
- Unsolicited Message Syntax 11
- Attention AT 12
- Repeat Last Command A/ 12
- Echo E 12
- Bits +WUSLMSK 13
- Chapter 4 – Identification 15
- Commands 15
- Chapter 5 – Query Commands 17
- Chapter 6 – Global 18
- Configuration Commands 18
- Save Configuration &W 19
- Chapter 7 – Status Commands 20
- Chapter 8 – Communication 26
- Set Diagnostic Port +WDMX 27
- Set DCD Signal &C 27
- Set DTR Signal &D 28
- Set DSR Signal &S 28
- Automatic Answer S0 30
- Command Edit Character S5 31
- Chapter 9 – Call Control 33
- Hang-Up Command H 34
- Answer a Call A 34
- Incoming Call +RING 35
- Emergency Mode +WSOS 37
- Call Answered +WANS 38
- Call Connected +WCNT 38
- Call Ended +WEND 39
- Call Originated +WORG 40
- CPHS Command +CPHS 40
- Call Forwarding +CCFC 42
- Send DTMF Tones +VTS 44
- Chapter 10 – Network Service 45
- Signal Quality +CSQ 46
- Band Preference +WBND 49
- Service Indication +WSRV 50
- Roam Preference +WRMP 50
- Default Cell Band +WDCB 51
- Roaming Indication +WROM 51
- Chapter 11 – Provisioning 54
- Control Commands 54
- Excess SPC Failures +WLCK 55
- Download PRL +DPRL 56
- Commit Changes +WCMT 58
- Set IMSI +WIMI 58
- Slot Cycle Index +WSCI 60
- SID and NID +WSID 60
- Chapter 12 – OTASP / OTAPA 61
- Commit Successful +WOTC 62
- SPL Unlocked +WOTS 62
- NAM Download OK +WOTN 62
- MDM Download OK +WOTM 62
- IMSI Download OK +WOTI 63
- PRL Download OK +WOTP 63
- Chapter 14 – Short Message 70
- Service Control Commands 70
- Read Message +CMGR 71
- List Message +CMGL 72
- Delete Message +CMGD 73
- Chapter 15 – Audio Commands 79
- Microphone Gain +VGT 81
- Speaker Gain Control +VGR 82
- Digital Gain Receive +WDGR 84
- Echo Cancellation +ECHO 86
- Speaker Driver Gain +WSDG 87
- Audio Loopback &T 88
- Chapter 16 – Data Commands 89
- R-SCH Selection $QCMIP 90
- MIP Selection $QCMIPP 91
- Chapter 17 – TCP APP AT 98
- Chapter 18 – Sleep Commands 107
- Builds) 111
- Chapter 19 – Antenna 111
- Commands (Not for IP and GPS 111
- +WANTPOLL 113
- Auxiliary GPS Power +WANT 115
- Scenarios 118
- Call Processing 119
- Sending Binary Data 120
- TCP Socket Examples 121
- TCP Server Example 122
- ATZ, and AT&F 123
- Chapter 22 – CDMA 128
- Terminology and Acronyms 128
Related products and manuals for Networking Multitech MultiModem Cell MTCBA-C1
Networking Multitech CDMA User's Guide
(32 pages)
(32 pages)
Networking Multitech ISIHP-4U User's Guide
(50 pages)
(50 pages)
Networking Multitech MVP 800 User's Guide
(88 pages)
(88 pages)
Networking Multitech ISIHP-4U Specifications
(44 pages)
(44 pages)
Networking Multitech MT5634ZBAV User's Guide
(170 pages)
(170 pages)
Networking Multitech GFU19 User Manual
(158 pages)
(158 pages)
Networking Multitech GFU19 Specifications
(18 pages)
(18 pages)
Networking Multitech MTC-C2 User's Guide
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 1.370 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals