Multitech MultiModem Cell MTCBA-C1 User's Guide Page 58
- Page / 135
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 11 – Provisioning Control Commands
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide (PN S000478C) 58
Access Overload Class +WAOC
Description: This command is used to set the Access Overload Class. If the +WAOC command is used
specifically to modify the AOC value, it will retain this value and will not be automatically updated via the WIMI or
WMDN commands. Otherwise, if the AOC has not been modified via the WAOC command, it will be automatically
updated to be the last digit of the MDN (WMDN) or IMSI (WIMI) when the commit (WCMT=1) command is issued.
Syntax: Command syntax: AT+WAOC=<number>
Command Possible Responses
A
T+WAOC?
Note: Get current Access Overload Class
+WAOC: 5
OK
A
T+WAOC=7
Note: Set Access Overload Class to 7
OK
Values: <number> Access overload value range:
0 to 15
Commit Changes +WCMT
Description: This command is used to commit or to undo/revert any changes done during the service
programming session. Changes performed during this session will not take place until a commit
command has been sent (AT+WCMT=1). Commission of these changes will force a software
reset of the modem. Sending this command indicates this service provisioning session is
complete. In order to perform any subsequent provisioning, the service programming code must
be entered using the +WSPC command.
Syntax: Command syntax: AT+WCMT=<val>
Command Possible Responses
AT+WCMT=0
Note: Undo any changes performed during this
provisioning AT session
OK
AT+WCMT=1
Note: Commit all changes performed during this
provisioning AT session to non-volatile memory.
OK
Note: software reset is performed
Values: <val>
0 undo changes
1 commit changes
Set IMSI +WIMI
Description: This command is used to set the IMSI. S valid IMSI is 15 digits in length: MCC (3), MNC (2),
MIN2 (3), MIN1 (7). For support of Wireless Number Portability, changes to the IMSI will NOT
update the MDN. If the MDN is modified via the WMDN command, the IMSI_M portion of the IMSI
will be automatically updated to the least significant 10 digits of the MDN, but the update will not
be visible or applied until the commit command is issued via the WCMT command. Changes to
the IMSI will automatically update Access Overload Class values unless specifically modified
using +WAOC.
Syntax: Command syntax: AT+WIMI=<number>
Command Possible Responses
AT+WIMI?
Note: Get current IMSI
+WIMI: 310008581111111
OK
AT+WIMI=310008585551212
Note: Set IMSI to 310008585551212
OK
- CDMA-C1 AT Commands 1
- Contents 3
- Chapter 1 – Introduction 7
- Chapter 2 – AT Commands 8
- Overview 8
- Command Types 9
- Command Format and Syntax 9
- Input Command Syntax 10
- Other Syntax 10
- Output Response Syntax 10
- Parameter Defaults 10
- Unsolicited Message Syntax 11
- Attention AT 12
- Repeat Last Command A/ 12
- Echo E 12
- Bits +WUSLMSK 13
- Chapter 4 – Identification 15
- Commands 15
- Chapter 5 – Query Commands 17
- Chapter 6 – Global 18
- Configuration Commands 18
- Save Configuration &W 19
- Chapter 7 – Status Commands 20
- Chapter 8 – Communication 26
- Set Diagnostic Port +WDMX 27
- Set DCD Signal &C 27
- Set DTR Signal &D 28
- Set DSR Signal &S 28
- Automatic Answer S0 30
- Command Edit Character S5 31
- Chapter 9 – Call Control 33
- Hang-Up Command H 34
- Answer a Call A 34
- Incoming Call +RING 35
- Emergency Mode +WSOS 37
- Call Answered +WANS 38
- Call Connected +WCNT 38
- Call Ended +WEND 39
- Call Originated +WORG 40
- CPHS Command +CPHS 40
- Call Forwarding +CCFC 42
- Send DTMF Tones +VTS 44
- Chapter 10 – Network Service 45
- Signal Quality +CSQ 46
- Band Preference +WBND 49
- Service Indication +WSRV 50
- Roam Preference +WRMP 50
- Default Cell Band +WDCB 51
- Roaming Indication +WROM 51
- Chapter 11 – Provisioning 54
- Control Commands 54
- Excess SPC Failures +WLCK 55
- Download PRL +DPRL 56
- Commit Changes +WCMT 58
- Set IMSI +WIMI 58
- Slot Cycle Index +WSCI 60
- SID and NID +WSID 60
- Chapter 12 – OTASP / OTAPA 61
- Commit Successful +WOTC 62
- SPL Unlocked +WOTS 62
- NAM Download OK +WOTN 62
- MDM Download OK +WOTM 62
- IMSI Download OK +WOTI 63
- PRL Download OK +WOTP 63
- Chapter 14 – Short Message 70
- Service Control Commands 70
- Read Message +CMGR 71
- List Message +CMGL 72
- Delete Message +CMGD 73
- Chapter 15 – Audio Commands 79
- Microphone Gain +VGT 81
- Speaker Gain Control +VGR 82
- Digital Gain Receive +WDGR 84
- Echo Cancellation +ECHO 86
- Speaker Driver Gain +WSDG 87
- Audio Loopback &T 88
- Chapter 16 – Data Commands 89
- R-SCH Selection $QCMIP 90
- MIP Selection $QCMIPP 91
- Chapter 17 – TCP APP AT 98
- Chapter 18 – Sleep Commands 107
- Builds) 111
- Chapter 19 – Antenna 111
- Commands (Not for IP and GPS 111
- +WANTPOLL 113
- Auxiliary GPS Power +WANT 115
- Scenarios 118
- Call Processing 119
- Sending Binary Data 120
- TCP Socket Examples 121
- TCP Server Example 122
- ATZ, and AT&F 123
- Chapter 22 – CDMA 128
- Terminology and Acronyms 128
Related products and manuals for Networking Multitech MultiModem Cell MTCBA-C1
Networking Multitech CDMA User's Guide
(32 pages)
(32 pages)
Networking Multitech ISIHP-4U User's Guide
(50 pages)
(50 pages)
Networking Multitech MVP 800 User's Guide
(88 pages)
(88 pages)
Networking Multitech ISIHP-4U Specifications
(44 pages)
(44 pages)
Networking Multitech MT5634ZBAV User's Guide
(170 pages)
(170 pages)
Networking Multitech GFU19 User Manual
(158 pages)
(158 pages)
Networking Multitech GFU19 Specifications
(18 pages)
(18 pages)
Networking Multitech MTC-C2 User's Guide
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 0.728 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals