Multitech MultiModem Cell MTCBA-C1 User's Guide Page 75
- Page / 135
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 14 – Short Message Service Control Commands
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide (PN S000478C) 75
New Message Indication +CNMI
Description: This command selects the procedure for message reception from the network. Note: Cell
Broadcast messages and Status Report messages are not stored.
Syntax: Command syntax: AT+CNMI=<mode>,<mt>,<bm>,<ds>,<bfr>
Command Possible Responses
AT+CNMI=2,1,0,0,0
Note: <mt>=1
OK
AT+CMTI : “MT”,1
Note: message received
AT+CNMI=2,2,0,0,0
Note: <mt>=2
OK
+CMT : “8585551212”,”98/10/01,12 :30 00”,
129,1,2,0,5<CR><LF>
Hello
Note: message received
AT+CNMI=2,0,0,1,0
Note: <ds>=1
OK
AT+CMGS=”8585551212”<CR>
Message to send <ctrl-Z>
Note: Send a message in text mode
+CMGS : 7
OK
Note: Successful transmission
+CDS : 2, 116, ”8585551212”, 129, “98/10/01,12 :30
:07”, “98/10/01 12 :30 :08”, 32768
Note: message was correctly delivered
Values <mode> The <mode> value controls the processing of unsolicited result codes. Only mode 2
is supported at this time.
2 Buffer unsolicited result codes in the TA when TA-TE link is reserved and flush them
to the TE after reservation. Otherwise forward the messages directly to the TE
without storing.
<mt> Sets the result code indication routing for SMS-DELIVERs. Default is 1.
0 No SMS-DELIVER indications are routed.
1 SMS-DELIVERs are routed using unsolicited code: +CMTI: “MT”, <index>
2 or 3 SMS-DELIVERs (except class 2 messages) are routed using unsolicited code:
+CMT: <oa>, <scts>, <tooa>, <lang>, <encod>,
<priority>[,<cbn>],<length><CR><LF><data> (text mode)
<bm> Sets the result code indication routing for received Cell Broadcast Messages. Default
is 0.
0 No CBM indications are routed to the TE. The CBMs are not stored.
2 or 3 New CBMs are routed directly to the TE using unsolicited result code (format
matches that of +CBM: <oa>, [<alpha>,] <scts> [,<tooa>, <length>]
<CR><LF><data> (text mode)
<ds> Sets the routing for SMS-STATUS-REPORTs. Default is 0.
0 No SMS-STATUS-REPORTs are routed.
1 SMS-STATUS-REPORTs are routed using unsolicited code: +CDS: <fo>, <mr>,
[<ra>] , [<tora>], <scts>, <dt>, <st> (Text mode)
<bfr> Since <mode> cannot be changed, this parameter is no longer used, but these
values are still accepted for legacy purposes. Default is 0.
0 TA buffer of unsolicited result codes defined within this command is flushed to the TE
when <mode> 1…3 is entered (OK response shall be given before flushing the
codes)
1 TA buffer of unsolicited result codes defined within this command is cleared when
<mode> 1…3 is entered.
- CDMA-C1 AT Commands 1
- Contents 3
- Chapter 1 – Introduction 7
- Chapter 2 – AT Commands 8
- Overview 8
- Command Types 9
- Command Format and Syntax 9
- Input Command Syntax 10
- Other Syntax 10
- Output Response Syntax 10
- Parameter Defaults 10
- Unsolicited Message Syntax 11
- Attention AT 12
- Repeat Last Command A/ 12
- Echo E 12
- Bits +WUSLMSK 13
- Chapter 4 – Identification 15
- Commands 15
- Chapter 5 – Query Commands 17
- Chapter 6 – Global 18
- Configuration Commands 18
- Save Configuration &W 19
- Chapter 7 – Status Commands 20
- Chapter 8 – Communication 26
- Set Diagnostic Port +WDMX 27
- Set DCD Signal &C 27
- Set DTR Signal &D 28
- Set DSR Signal &S 28
- Automatic Answer S0 30
- Command Edit Character S5 31
- Chapter 9 – Call Control 33
- Hang-Up Command H 34
- Answer a Call A 34
- Incoming Call +RING 35
- Emergency Mode +WSOS 37
- Call Answered +WANS 38
- Call Connected +WCNT 38
- Call Ended +WEND 39
- Call Originated +WORG 40
- CPHS Command +CPHS 40
- Call Forwarding +CCFC 42
- Send DTMF Tones +VTS 44
- Chapter 10 – Network Service 45
- Signal Quality +CSQ 46
- Band Preference +WBND 49
- Service Indication +WSRV 50
- Roam Preference +WRMP 50
- Default Cell Band +WDCB 51
- Roaming Indication +WROM 51
- Chapter 11 – Provisioning 54
- Control Commands 54
- Excess SPC Failures +WLCK 55
- Download PRL +DPRL 56
- Commit Changes +WCMT 58
- Set IMSI +WIMI 58
- Slot Cycle Index +WSCI 60
- SID and NID +WSID 60
- Chapter 12 – OTASP / OTAPA 61
- Commit Successful +WOTC 62
- SPL Unlocked +WOTS 62
- NAM Download OK +WOTN 62
- MDM Download OK +WOTM 62
- IMSI Download OK +WOTI 63
- PRL Download OK +WOTP 63
- Chapter 14 – Short Message 70
- Service Control Commands 70
- Read Message +CMGR 71
- List Message +CMGL 72
- Delete Message +CMGD 73
- Chapter 15 – Audio Commands 79
- Microphone Gain +VGT 81
- Speaker Gain Control +VGR 82
- Digital Gain Receive +WDGR 84
- Echo Cancellation +ECHO 86
- Speaker Driver Gain +WSDG 87
- Audio Loopback &T 88
- Chapter 16 – Data Commands 89
- R-SCH Selection $QCMIP 90
- MIP Selection $QCMIPP 91
- Chapter 17 – TCP APP AT 98
- Chapter 18 – Sleep Commands 107
- Builds) 111
- Chapter 19 – Antenna 111
- Commands (Not for IP and GPS 111
- +WANTPOLL 113
- Auxiliary GPS Power +WANT 115
- Scenarios 118
- Call Processing 119
- Sending Binary Data 120
- TCP Socket Examples 121
- TCP Server Example 122
- ATZ, and AT&F 123
- Chapter 22 – CDMA 128
- Terminology and Acronyms 128
Related products and manuals for Networking Multitech MultiModem Cell MTCBA-C1
Networking Multitech CDMA User's Guide
(32 pages)
(32 pages)
Networking Multitech ISIHP-4U User's Guide
(50 pages)
(50 pages)
Networking Multitech MVP 800 User's Guide
(88 pages)
(88 pages)
Networking Multitech ISIHP-4U Specifications
(44 pages)
(44 pages)
Networking Multitech MT5634ZBAV User's Guide
(170 pages)
(170 pages)
Networking Multitech GFU19 User Manual
(158 pages)
(158 pages)
Networking Multitech GFU19 Specifications
(18 pages)
(18 pages)
Networking Multitech MTC-C2 User's Guide
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 0.323 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals