Multitech MultiModem Cell MTCBA-C1 User's Guide Page 52
- Page / 135
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 10 – Network Service Commands
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide (PN S000478C) 52
Cell Environment and RxLev Indication +CCED
Description: This command can be used by the application to retrieve information about the main cell and up
to six neighboring cells. This is an extended command that may be used in two different settings:
1. Interrogation of the cell environment information
2. Interrogation of the received signal strength indication (RSSI)
The +CCED command supports two modes of operation: on request by the application or
automatically by the product every 5 seconds. Signal strength can also be reported when the
change exceeds a threshold.
Syntax: Command syntax: AT+CCED=<mode>[, <requested dump>[,<sqStep>]]
Command Possible Responses
AT+CCED=? +CCED: (0-2),(1,8,9),(1-5)
OK
AT+CCED?
Note: <requested dump> is the most
recently requested one. If none
requested, <requested dump>=1 will be
displayed.
+CCED: 0,1,0
OK
AT+CCED=0
Note: One time dump of the <requested
dump> that was last requested. If none
requested, <requested dump>=1 will be
displayed
+CSQ: 15, 99
or
+CCED: 0,160,69,101,6,144,2690,2,18,-85,-51,-63
OK
AT+CCED=0,1
Note: one time, dump main cell
+CCED: 0,160,69,101,6,144,2690,2,18,-85,-51,-63
OK
AT+CCED
Note: one time, previous <requested
dump> value is used
+CCED: 0,160,69,101,6,144,2690,2,18,-85,-51,-63
OK
AT+CCED =0,9
+CSQ: 15, 99
+CCED: 0,160,69,101,6,144,2690,2,18,-85,-51,-63
OK
AT+CCED=1,8
Note: Start automatic snapshots and
dump <rssi>.
OK
+CSQ: 18, 99
Note: +CSQ response output every 5 seconds.
AT+CCED=2 OK
Note: Stop automatic snapshots.
AT+CCED=,,1 OK
+CSQ: 18, 99
Note: New +CSQ response output when change in
RSSI equals or exceeds <CsqStep>
AT+CCED=1,9
Note: Start automatic snapshots and
dump cell environment and <rssi>
OK
+CSQ: 15, 99
+CCED: 0,160,69,101,6,144,2690,2,18,-85,-51,-63
Values: <mode>
0 Requests a single snapshot of cell data
1 Start automatic snapshot mode. The unsolicited responses +CCED and/or
+CSQ will be used to return the requested information.
2 Stop automatic snapshot mode
<requested dump> This parameter is specified as the summation of one or more of the
following values:
1 Main Cell Indication
2 Main Cell RSSI Indication (RxLev) from 0 to 31 and frame error rate. Set
the AT+CSQ command description for more information.
<CsqStep>
0 Unsolicited +CSQ reports due to changing RSSI levels are disabled.
1-5: Whenever the RSSI changes by this amount or more, an unsolicited +CSQ
report is generated.
- CDMA-C1 AT Commands 1
- Contents 3
- Chapter 1 – Introduction 7
- Chapter 2 – AT Commands 8
- Overview 8
- Command Types 9
- Command Format and Syntax 9
- Input Command Syntax 10
- Other Syntax 10
- Output Response Syntax 10
- Parameter Defaults 10
- Unsolicited Message Syntax 11
- Attention AT 12
- Repeat Last Command A/ 12
- Echo E 12
- Bits +WUSLMSK 13
- Chapter 4 – Identification 15
- Commands 15
- Chapter 5 – Query Commands 17
- Chapter 6 – Global 18
- Configuration Commands 18
- Save Configuration &W 19
- Chapter 7 – Status Commands 20
- Chapter 8 – Communication 26
- Set Diagnostic Port +WDMX 27
- Set DCD Signal &C 27
- Set DTR Signal &D 28
- Set DSR Signal &S 28
- Automatic Answer S0 30
- Command Edit Character S5 31
- Chapter 9 – Call Control 33
- Hang-Up Command H 34
- Answer a Call A 34
- Incoming Call +RING 35
- Emergency Mode +WSOS 37
- Call Answered +WANS 38
- Call Connected +WCNT 38
- Call Ended +WEND 39
- Call Originated +WORG 40
- CPHS Command +CPHS 40
- Call Forwarding +CCFC 42
- Send DTMF Tones +VTS 44
- Chapter 10 – Network Service 45
- Signal Quality +CSQ 46
- Band Preference +WBND 49
- Service Indication +WSRV 50
- Roam Preference +WRMP 50
- Default Cell Band +WDCB 51
- Roaming Indication +WROM 51
- Chapter 11 – Provisioning 54
- Control Commands 54
- Excess SPC Failures +WLCK 55
- Download PRL +DPRL 56
- Commit Changes +WCMT 58
- Set IMSI +WIMI 58
- Slot Cycle Index +WSCI 60
- SID and NID +WSID 60
- Chapter 12 – OTASP / OTAPA 61
- Commit Successful +WOTC 62
- SPL Unlocked +WOTS 62
- NAM Download OK +WOTN 62
- MDM Download OK +WOTM 62
- IMSI Download OK +WOTI 63
- PRL Download OK +WOTP 63
- Chapter 14 – Short Message 70
- Service Control Commands 70
- Read Message +CMGR 71
- List Message +CMGL 72
- Delete Message +CMGD 73
- Chapter 15 – Audio Commands 79
- Microphone Gain +VGT 81
- Speaker Gain Control +VGR 82
- Digital Gain Receive +WDGR 84
- Echo Cancellation +ECHO 86
- Speaker Driver Gain +WSDG 87
- Audio Loopback &T 88
- Chapter 16 – Data Commands 89
- R-SCH Selection $QCMIP 90
- MIP Selection $QCMIPP 91
- Chapter 17 – TCP APP AT 98
- Chapter 18 – Sleep Commands 107
- Builds) 111
- Chapter 19 – Antenna 111
- Commands (Not for IP and GPS 111
- +WANTPOLL 113
- Auxiliary GPS Power +WANT 115
- Scenarios 118
- Call Processing 119
- Sending Binary Data 120
- TCP Socket Examples 121
- TCP Server Example 122
- ATZ, and AT&F 123
- Chapter 22 – CDMA 128
- Terminology and Acronyms 128
Related products and manuals for Networking Multitech MultiModem Cell MTCBA-C1
Networking Multitech CDMA User's Guide
(32 pages)
(32 pages)
Networking Multitech ISIHP-4U User's Guide
(50 pages)
(50 pages)
Networking Multitech MVP 800 User's Guide
(88 pages)
(88 pages)
Networking Multitech ISIHP-4U Specifications
(44 pages)
(44 pages)
Networking Multitech MT5634ZBAV User's Guide
(170 pages)
(170 pages)
Networking Multitech GFU19 User Manual
(158 pages)
(158 pages)
Networking Multitech GFU19 Specifications
(18 pages)
(18 pages)
Networking Multitech MTC-C2 User's Guide
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 0.436 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals