Multitech MMH900 User's Guide Page 58
- Page / 200
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
58
Chapter 5 - Commands
The H command menu is as follows:
General Help
- Each command line must begin with the prefix AT.
- Each command line may contain any number of commands up to
40
characters total.
- Most command letters must be followed by a value.
- For help on specific commands, enter "ATH" followed by one of the
command letters.
ATH1 for channel parameter commands.
ATH2 to view the DIP switch configurations.
ATH3 for async and sync composite link format commands.
ATH4 for additional composite link commands.
ATH5 for miscellaneous commands.
ATH6 for internal V.29/V.33 composite link modem commands.
ATH7 for internal DSU commands.
ATH8 for internal MMH2834 modem commands
For additional help menus, enter one of the following ATH codes to
obtain the desired information:
ATH or ATH0 for General Help.
- MMH900 Series Statistical 1
- Multiplexer 1
- User Guide 1
- S000315A Revision A 2
- Contents 3
- Description 7
- 1.1 Introduction 8
- 1.2 About This Manual 8
- 1.3 Background 10
- 1.3.1.2 Communications 12
- 1.4 Product Description 13
- 1.5 System Features 16
- 1.5.1 Response Time Control 16
- 1.5.2 Dynamic Buffering 16
- 1.5.3 Flow Control 17
- 1.5.4 Diagnostics 17
- Reporting 18
- 1.5.7 Parameter Memory 18
- 1.5.8 Channel Flexibility 18
- 1.5.9 Command Modem 18
- 1.5.10 Composite Link 19
- Interconnection 20
- 1.7 DOC Terminal Equipment 22
- 1.8 Specifications 23
- 1.8.1 Channels 23
- 1.8.2 System Control 23
- 1.8.3 Composite LInk 24
- 1.8.4 33,600 bps Link Modem 24
- 1.8.5 56,000 bps DSU 24
- 1.8.6 ISDN Terminal Adapter 25
- 1.8.7 Command Modem 25
- 1.8.8 Electrical/Physical 25
- Chapter 2 - Configuration 26
- 2.1 Introduction 27
- 2.2 Configuration 1 28
- 2.3 Configuration 2 30
- 2.4 Configuration 3 31
- Descriptions 33
- 3.1 Introduction 34
- 3.2 Front Panel 34
- 3.3 LED Indicators 35
- Internal Composite Link (DSU) 37
- Internal Link Device (Modems) 38
- COMPOSITE LINK 39
- 3.5 Switches/Jumper/Shunt 41
- 3.5.1 8-Position DIP Switch 41
- 3.5.2 4-Position DIP Switch 42
- 3.5.3 144RKWL/OtherJumper 43
- 3.5.4 V.24/V.35 Shunt 43
- Chapter 4- Installation 44
- 4.1 Introduction 45
- 4.2 Safety Warnings 45
- 4.3 Unpacking 45
- RS232C/V.35 46
- INTERNAL 46
- V.35 V.24 47
- Supervisory Console 48
- Channels 49
- Parameters (&W) command 50
- Chapter 4 - Installation 50
- Chapter 5 - Commands 51
- 5.1 Introduction 52
- 5.2 Command Description 57
- 5.2.1 General Commands 57
- The H1 Menu is as follows: 59
- The H2 Menu is as follows: 60
- UP = 16/32 MM 60
- DN = 900 MMH/MMV 60
- The H3 Mend is as follows: 61
- The H4 Menu is as follows: 61
- The H5 Menu is as follows: 62
- The H6 Menu is as follows: 62
- The H7 Menu is as follws: 63
- The H8 Menu is as follows: 63
- CHANNEL DEVICE 66
- INITIATED PACING 66
- MultiMux 67
- 5.2.3 Composite Link Commands 73
- LINE LOAD TYPE TIMER TIME 75
- OFF INTERNAL 10ms 3 75
- 5.2.8 Test Commands 86
- 5.2.9 Command Modem commands 88
- Chapter 6- Operating 89
- Procedures 89
- 6.1 Introduction 90
- Chapter 7 - Troubleshooting 96
- 7.1 Introduction 97
- 7.3 Test Cables 98
- Composite Link 99
- Loopback Cable 99
- 7.4 Troubleshooting Guide 100
- Channel device losing data 105
- 7.5 Channel Device Testing 106
- Procedure 107
- Technical Support 111
- 8.1 Introduction 112
- 8.2 Warranty 112
- Customers 113
- Distributors 115
- Appendices 116
- Appendix A 117
- Appendix B 118
- Appendix C - Cabling Diagrams 120
- Channel Cables 120
- Command Port Cables 121
- Appendix D 124
- Command Modem Commands 124
- Appendix F 142
- Flow Control Background 142
- MiniComputer Flow Control 143
- Appendix G 145
- MMH2834 S-Registers 145
- Appendix H 148
- Dial Back-up 148
- Appendix I 149
- Testing Your MMH2834 149
- I.1 Introduction 149
- Local MultiModem 150
- Type ATU0 or ATU1; hit ENTER 150
- Digital Analog DigitalAnalog 151
- I.5 Synchronous Mode Testing 155
- Digital Analog 156
- AnalogDigital Analog 157
- DigitalAnalogDigital Analog 158
- Modem Commands 159
- J.1 Introduction 159
- #S Change SETUP Password 161
- J.1.1 Dialing Action Commands 162
- J.1.2 Dial Modifier Commands 164
- Commands 171
- Immediate Action Commands 182
- Glossary 184
- S000315A 200
Related products and manuals for Networking Multitech MMH900
Networking Multitech MVP200 User's Guide
(44 pages)
(44 pages)
Networking Multitech MA30120 User's Guide
(29 pages)
(29 pages)
Networking Multitech MTCMR-G2 User's Guide
(29 pages)
(29 pages)
Networking Multitech MTPSR1-202ST User's Guide
(104 pages)
(104 pages)
(13 pages)
Networking Multitech MT202TD User's Guide
(28 pages)
(28 pages)
Networking Multitech MTCMR-H User's Guide
(36 pages)
(36 pages)
Networking Multitech MTCMR-E User's Guide
(54 pages)
(54 pages)
Networking Multitech MT2834MRK Manual
(31 pages)
(31 pages)
Networking Multitech GFU19 User Manual
(152 pages)
(152 pages)
© 2020, manymanuals.com. All rights reserved. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals