078-0346-01E®i.LON®SmartServer 2.0 Hardware Guide
x Preface Region Languages Supported Contact Information Europe English German French Italian Echelon Europe Ltd. Suite 12 Building 6 Croxley
i.LON SmartServer 2.0 Hardware Guide 1 1 Assembling the SmartServer Hardware This chapter describes how to mount the SmartServer hardware inside a
2 Assembling the SmartServer Hardware Assembly Overview You need to assemble the SmartServer and connect it to a TCP/IP network before you can conf
i.LON SmartServer 2.0 Hardware Guide 3 b. Open Internet Explorer 6 or later and enter the following URL: 192.168.1.222. Your SmartServer home pag
4 Assembling the SmartServer Hardware
i.LON SmartServer 2.0 Hardware Guide 5 Wiring the SmartServer Connections After you mount the SmartServer, you can wire its connections. The Smart
6 Assembling the SmartServer Hardware Connecting the Screw Terminals The SmartServer has two rows of screw terminals located on the top and bottom
i.LON SmartServer 2.0 Hardware Guide 7 ! Safety Warning The SmartServer uses a Poly-carbonmonoflouride Lithium Coin battery. RISK OF EXPLOSION IF B
8 Assembling the SmartServer Hardware The following table lists the enclosure marking for each of the high-voltage AC power mains screw terminals
i.LON SmartServer 2.0 Hardware Guide 9 ! Sicherheitshinweis: Vorsicht Netzspannung! Stellen Sie sicher, daß die Netzspannung ausgeschaltet wurde
ii Preface Echelon, i.LON, LON, LONORKS, LonTalk, Neuron, LONMARK, 3120, 3150, LNS, LonMaker, and the Echelon logo are trademarks of Echelon Corpora
10 Assembling the SmartServer Hardware The following table lists the enclosure markings for the LONWORKS network screw terminals on the SmartServe
i.LON SmartServer 2.0 Hardware Guide 11 The following table lists the enclosure markings for the RS-232 and RS-485 port screw terminals and on the
12 Assembling the SmartServer Hardware Notes: If your external GSM modem requires a carrier detect line, you can attach one end of a 22-gauge (AWG)
i.LON SmartServer 2.0 Hardware Guide 13 Connecting Legacy or Nonnative Devices to the RS-232 and RS-485 Serial Ports You can connect legacy system
14 Assembling the SmartServer Hardware 6 Output 1 Relay output 1 7 Output 2 Relay output 2 8 Output 2 Relay output 2 You can connect the dry
i.LON SmartServer 2.0 Hardware Guide 15 The following table lists the enclosure markings for the pulse meter input screw terminals on the SmartSer
16 Assembling the SmartServer Hardware Digital Inputs The SmartServer has two optically isolated, polarity-sensitive digital inputs that you can us
i.LON SmartServer 2.0 Hardware Guide 17 +12V < 20mA Output The SmartServer contains one +12VDC outlet that can provide up to 20mA. The +12V &l
18 Assembling the SmartServer Hardware Connecting the Ethernet Port After you have connected all the required screw terminals on the SmartServer fo
i.LON SmartServer 2.0 Hardware Guide 19 Note: Pin 1 of the RS-232 console port can be attached to the carrier detect line of an external GSM modem
i.LON SmartServer 2.0 Hardware Guide iii Table of Contents Preface ...
20 Assembling the SmartServer Hardware
i.LON SmartServer 2.0 Hardware Guide 21 2 Using the SmartServer LEDs and Service Buttons This chapter describes how to use the LEDs and service
22 Using the SmartServer Service Buttons and LEDs Using the SmartServer LEDs The SmartServer has a number of LEDs that provide status information.
i.LON SmartServer 2.0 Hardware Guide 23 LON BIU/RX For PL-20 models of the SmartServer, this LED is the Band In Use (BIU) indicator. It lights whe
24 Using the SmartServer Service Buttons and LEDs shortcut menu. The Setup – Reboot dialog opens. Click Reboot to start the reboot. • To reboot
www.echelon.com
iv Preface Preface The i.LON® SmartServer is a low-cost, high-performance controller, network manager, router, remote network interface, and Web ser
i.LON SmartServer 2.0 Hardware Guide v FCC Compliance Statement – Class B This equipment has been tested and found to comply with the limits for
vi Preface Welcome The SmartServer is a low-cost, high-performance controller, network manager, router, remote network interface, and Web server tha
i.LON SmartServer 2.0 Hardware Guide vii The following table lists the SmartServer model numbers, the features included with the model, and the pow
viii Preface • 64 MB SDRAM • 64 MB NAND flash memory • 2,048 bytes EEPROM • 2MB bootROM • Extended temperature (-40 to 60°C) for PL model compo
i.LON SmartServer 2.0 Hardware Guide ix • LNS® Programmer’s Guide. Describes how to write LNS applications that take advantage of the network des
Comments to this Manuals